[Dec 15, 2021] Verified NACE-CIP2-001 dumps and 100 unique questions
NACE-CIP2-001 Dumps for Pass Guaranteed - Pass NACE-CIP2-001 Exam 2021
NEW QUESTION 46
The most likely area of failure on a buried external pipeline coating is the:
- A. Ground bed
- B. Field joint coating
- C. Areas exposed to Ultra Violet light
- D. Mainline coating
Answer: B
NEW QUESTION 47
Inspection and Test plans are developed by referencing:
- A. The Specification, SDS, relevant Standards and Codes
- B. The Specification, Application Guidelines, 'Relevant Standards and Codes
- C. The Specification, Safety Manual, Relevant Standards and Codes
- D. The Specification, TDS, relevant Standards and Codes
Answer: D
NEW QUESTION 48
NACE No.13/ SSPC 6 identifies the use of:
- A. Watterjetting only
- B. Steam cleaning only
- C. Various methods of cleaning
- D. Abrasive blasting only
Answer: C
NEW QUESTION 49
Corrosion is the reverse process of
- A. flaking.
- B. steel manufacturing.
- C. galvanic deterioration.
- D. hot dipping.
Answer: B
NEW QUESTION 50
You are a NACE Level 2 in-house inspector working in a shop. Your in-house requires you to perform a sleeve test to test for soluble salts; however the 3 rd party NACE Level 3 inspector, the owner, has a san smart meter and has achieved a very different result and has rejected the pre-cleaning.
Your FIRST course of action is to:
- A. Advise the other inspector he is using an incorrect method
- B. Advise your QC Manager to change the ITP to the use of the salt smart meter
- C. Redo the pre-cleaning based on the other inspectors results
- D. Review the specification with the other inspector to see what method was specified
Answer: D
NEW QUESTION 51
You are the NACE Coating Inspector on a tank lining project and are asked to perform a high voltage holiday test after the coating applicators have completed their final repairs. After meeting all the confined space entry permit you enter the tank and notice a very strong odor of solvent.
Your first course of action should to:
- A. Investigate to find the source of the odor
- B. Exit the tank and immediately and report the problem to the nearest safety supervisor
- C. Don your air supplied respirator and continue the testing
- D. Exit the tank and document the incident in your daily report
Answer: B
NEW QUESTION 52
When using a destructive Paint Inspection Gauge the NACE inspector must:
- A. Determine the Dry Film Thickness of the coating prior to use
- B. Ensure the glue on the dolly is properly applied prior to use
- C. Consult SSPC Guide 1 prior to use
- D. Select the appropriate hand wheel based on the measured Dry Film Thickness prior to us
Answer: A
NEW QUESTION 53
From a corrosion perspective, the main difference between Ferrous and Non-Ferrous Metals is:
- A. Appearance
- B. Cost
- C. Safety
- D. Iron content
Answer: D
NEW QUESTION 54
In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?
- A. Cure stage
- B. Flow stage
- C. Wetting stage
- D. Gel stage
Answer: B
NEW QUESTION 55
Which surface preparation method uses a dilute acid solution to remove laitance and I roughen the concrete surface?
- A. Acid etching
- B. High-pressure water washing
- C. Sacking
- D. Stoning
Answer: A
NEW QUESTION 56
Antifouling coatings are regulated by international treaties.
- A. False
- B. True
Answer: B
NEW QUESTION 57
Inspector reports should always be copied to:
- A. All parties involved in the project
- B. The Owner only
- C. The Contractor and Owner
- D. Whomever the Owner identifies
Answer: D
NEW QUESTION 58
Eddy current DFT gauges are used to measure Dry Film Thickness in which of the following situations:
- A. Conductive coatings applied to a cementitious substrate
- B. Non-Conductive coatings applied to a conductive metallic substrate
- C. Conductive coatings applied to a magnetic metallic substrate
- D. Magnetic coatings applied to a magnetic metallic substrate
Answer: B
NEW QUESTION 59
A single component water borne acrylic coating cures by:
- A. Solvent Evaporation
- B. Coalescence
- C. Co-Reaction
- D. Oxidation
Answer: B
NEW QUESTION 60
When performing inspection in accordance with ASTM D 4138 the Inspector will use:
- A. A set of 14 pencils of varying hardness
- B. A mechanical adhesion tester
- C. A destructive paint inspection Tooke gauge
- D. A hardness tester
Answer: C
NEW QUESTION 61
The cost of qualified Coating Inspection is normally offset by:
- A. Lower Application Costs
- B. Lower Safety Enforcement Costs
- C. Lower Coating Life Cycle Costs
- D. Lower Supervision Costs
Answer: C
NEW QUESTION 62
When a coating is expected to be exposed to temperatures above 93C (200 F) the best choice would be:
- A. Latex
- B. Organic coatings
- C. Inorganic Coatings
- D. Polyurea
Answer: C
NEW QUESTION 63
You are a NACE Level 2 Coating Inspector who has just arrived on a job in progress where there is no Inspection and Test Plan (ITP). The first morning you arrive the job is behind schedule and you are asked to take DIY Film Thickness readings.
Your FIRST preferred course of action is to:
- A. Use a generally accepted industry standard and to take readings
- B. Refuse to take readings until an is in place
- C. Develop your own methodology and proceed take the readings
- D. Call your supervisor
Answer: A
NEW QUESTION 64
You are the new NACE Level 2 Inspector on a job which had been very problematic. The previous Inspector was fired duo to personality conflicts with the Contractor's supervisor. Upon arriving onsite the Contractor's supervisor advises you in no uncertain terms that you will be the next to go, unless you cooperate with him.
Your FIRST preferred course of action is to:
- A. Suggest to the Owner that the supervisor should be removed from site
- B. Challenge the supervisor's authority
- C. Defend the previous inspector
- D. Express a willingness to work with the site team and follow the specification
Answer: D
NEW QUESTION 65
Coating Surveys are legally required:
- A. On commercial marine vessels and offshore platforms
- B. On high pressure gas lines and fireproofed structures
- C. On water tanks and potable water pipelines
- D. On food and beverage vessels and can linings
Answer: A
NEW QUESTION 66
Dehumidification is defined as the removal of moisture vapor from the air to
- A. provide worker comfort.
- B. lower its dew point,
- C. raise its relative humidity.
- D. lower its temperature
Answer: B
NEW QUESTION 67
The standards defining surface cleanliness achieved by centrifugal blast cleaning are:
- A. Slightly different to air blast cleaning
- B. Comparable to air blast cleaning
- C. The same as air blast cleaning
- D. Different than air blast cleaning
Answer: C
NEW QUESTION 68
Differences in technique for abrasive blasting concrete versus steel require the operator to:
- A. a), b) and c)
- B. Lower the blast pressure
- C. Move the nozzle quicker
- D. Increase the standoff distance
Answer: A
NEW QUESTION 69
When ASIN D 3363 is specified the Inspector must:
- A. Record the percentage of failure
- B. Use the correct solvent
- C. Record the highest value attained
- D. Record the two end points identified in the standard
Answer: D
NEW QUESTION 70
When observing design defects the NACE Inspector should:
- A. Ignore the defect as the inspector can't change the design
- B. Stop the job immediately
- C. Request that the item be rebuilt with a better design for coating
- D. Document the defect and the potential problems that could result
Answer: D
NEW QUESTION 71
......
Latest 100% Passing Guarantee - Brilliant NACE-CIP2-001 Exam Questions PDF: https://www.troytecdumps.com/NACE-CIP2-001-troytec-exam-dumps.html
NACE-CIP2-001 Exam Dumps - Try Best NACE-CIP2-001 Exam Questions: https://drive.google.com/open?id=1NCQWgAeJl7HZIeyXLtHXoh67wY6Nn_go