HPE6-A73 Free Exam Questions and Answers PDF Updated on Nov-2024
Latest HPE6-A73 Exam Dumps Recently Updated 130 Questions
What is the cost of Hewlett Packard Enterprise Aruba Certified Switching Professional Exam
The cost of Hewlett Packard Enterprise Aruba Certified Switching Professional Examis $300.
- Length of Examination: 140 minutes
- Number of Questions: 120
- Format: Multiple choices, various answers
NEW QUESTION # 29
Examine the attached diagram.
The two PCs are located in VLAN 11 (10.1.11.0/24). Which example defines how to implement active gateway on the VSX core for VLAN 11?
- A. interface lag 254
active-gateway ip 10.1.11.1
active-gateway mac 02:02:00:00:01:00 - B. interface vlan 11
active-gateway ip 10.1.11.1
active-gateway mac 02:02:00:00:01:00 - C. vsx
vrrp group 1 - D. interface lag 254
active-gateway vlan 11 ip 10.1.11.1
active-gateway vlan 11 mac 02:02:00:00:01:00
Answer: B
NEW QUESTION # 30
An administrator is configuring BGP and has two connections to a service provider to two different local routers.
Which BGP metric should the administrator configure to influence which local router the service provider will use to reach certain routes?
- A. Local preference
- B. Multiple exit discriminator
- C. Weight
- D. Origin
Answer: B
NEW QUESTION # 31
Examine the following AOS-CX switch configuration:
Which statement correctly describes what is allowed for traffic entering interface 1/1/3?
- A. IP traffic from 10.1.11.0/24 is allowed to access 10.1.110.0/24
- B. IP traffic from 10.1.12.0/24 is allowed to access 172.0.1.0/23
- C. IP traffic from 10.0.11.0/24 is allowed to access 10.1.12.0/24
- D. Traffic from 10.0.12.0/24 will generate a log record when accessing 10.0.11.0/24
Answer: C
NEW QUESTION # 32
A company has just purchased AOS-CX switches. The company has a free and open-source AAA solution.
The company wants to implement access control on the Ethernet ports of the AOS-CX switches.
Which security features can the company implement given the equipment that they are using?
- A. Downloadable user roles
- B. Local user roles
- C. Port-based tunneling
- D. Device fingerprinting
Answer: B
NEW QUESTION # 33
An administrator is defining a VSX LAG on a pair of AOS-CX switches that are defined as pnmary and secondary The VSX LAG fails to establish successfully with a remote switch; however, after verification, the remote switch is configured correctly. The administrator narrows down the problem to the configuration on the AOS-CX switches.
What would cause this problem?
- A. Local optimization was not enabled on the VSX LAG
- B. LACP was enabled in active mode on the VSX LAG
- C. The VSX LAG interfaces are in layer-3 mode
- D. The VSX LAG hash does not match the remote peer
Answer: D
NEW QUESTION # 34
Which concept is implemented using Aruba's dynamic segmentation?
- A. Root of trust
- B. Colorless port
- C. Zero Touch Provisioning
- D. Device fingerprinting
Answer: D
Explanation:
Explanation/Reference:
NEW QUESTION # 35
How does PIM build the IP multicast routing table to route traffic between a multicast source and one or more receivers?
- A. It uses the shortest path first (SPF) algorithm derived from link state protocols
- B. It uses IGMP and calculates a shortest path tree (SPT)
- C. It uses the unicast routing table and reverse path forwarding (RPF)
- D. It uses the Bellman-Ford algorithm derived from distance vector protocols
Answer: C
NEW QUESTION # 36
Which does VOQ implement that is different from most typical campus switches?
- A. Large egress packet buffers
- B. Large ingress packet buffers
- C. Per-port ASICs
- D. vsx
Answer: D
NEW QUESTION # 37
Which statement is correct regarding ACLs and TCAM usage?
- A. Applying an ACL to a group of VLANs consumes the same resources as specific ACE entries
- B. Using object groups consumes the same resources as specific ACE entries
- C. Applying an ACL to a group of ports consumes the same resources as specific ACE entries
- D. Compression is automatically enabled for ASIC TCAMs on AOS-CX switches
Answer: B
NEW QUESTION # 38
Examine the network topology.
The network is configured for OSPF with the following attributes:
Here is the OSPF configuration performed on Core1:
Based on the above information, what is correct?
- A. Area 0 has 81 routes
- B. Area 1 has 23 routes
- C. Corel has received one type 5 LSA from the ASBR.
- D. ISP 1 is not reachable from any area.
Answer: A
NEW QUESTION # 39
How is voice traffic prioritized correctly on AOS-CX switches?
- A. By implementing weighted fair queueing (WFQ)
- B. By defining device profiles with QOS settings
- C. By placing it in the strict priority queue
- D. By implementing voice VLANs
Answer: C
NEW QUESTION # 40
An administrator wants to track what configuration changes were made on a switch What should the administrator implement to see the configuration changes on an AOS-CX switch?
- A. Network Analysis Engine (NAE)
- B. AAA authorization
- C. VSX synchronization logging
- D. AAA authentication
Answer: A
NEW QUESTION # 41
An AOS-CX switch is configured to implement downloadable user roles. Examine the AOS-CX switch output:
Based on this output, what is the state of the user's access?
- A. MAC authentication has passed, but 802.1X authentication is in progress
- B. The port should be configured for 802.1X
- C. No downloadable user role exists
- D. The RADIUS request timed out to the AAA server
Answer: B
NEW QUESTION # 42
What is a best practice concerning voice traffic and dynamic segmentation on AOS-CX switches?
- A. Switch authentication and user-based tunneling of the voice traffic
- B. Controller authentication and user-based tunneling of the voice traffic
- C. Controller authentication and port-based tunneling of the voice traffic
- D. Switch authentication and local forwarding of the voice traffic
Answer: C
NEW QUESTION # 43
A company is implementing AOS-CX switches at the access layer. The company wants to implement access control for employees and guests.
Which security features will require a ClearPass server to be installed and used by the company?
- A. Change of authorization (CoA)
- B. User-based tunneling (UBT)
- C. Downloadable user roles
- D. Dynamic segmentation
Answer: D
NEW QUESTION # 44
What is correct regarding rate limiting and egress queue shaping on AOS-CX switches?
- A. Rate limiting and egress queue shaping can be applied globally
- B. Only a traffic rate and burst size can be defined for a queue
- C. Rate limiting and egress queue shaping can be used to restrict inbound traffic
- D. Limits can be defined only for broadcast and multicast traffic
Answer: B
Explanation:
you could apply egress queue shaping to the high priority queues to prevent starvation of low priority queues. Egress queue shaping allows you to apply a maximum bandwidth to a priority queue, as well as a burst size. The port buffers excess traffic up to the burst size and sends the buffered traffic at the max rate, smoothing out bursts while also preventing the high priority queue from exceeding its maximum rate and starving out lower priority queues.
NEW QUESTION # 45
An administrator is concerned about the security of the control plane connection between an AOS-CX switch and an ArubaMobility Controller (MC) when implementing user-based tunneling How should the administrator protect this traffic?
- A. IPSec with a digital certificate
- B. GRE with a pre-shared Key
- C. IPSec with a pre-shared key
- D. PAPI with an MD5 pre-shared key
Answer: D
NEW QUESTION # 46
Examine the network exhibit:
The ACL configuration defined on Core-1 is as follows:
If telnet was being used, which device connection would be permitted and functional in both directions?
(Choose two.)
- A. Client 1 to Client 3
- B. Server 1 to Client 1
- C. Client 1 to Client 2
- D. Client 3 to Client 2
- E. Server 2 to Client 2
Answer: B,C
Explanation:
CL3 - CL2 - drop on forward path by core1 cause match VLAN 20 and CL3 not CL1 as SRC IP CL1 - CL2 - pass - no ACL cause forwarded by Access2 SR2 - CL2 - pass on forward path by core1 cause match VLAN 10 Drop on return path by core1 cause match VLAN 20 and no CL1 as SRC IP SR1 - CL1 - pass on forward path by core1 cause match VLAN 10 pass on return path by core1 cause match VLAN 20 and CL1 as SRC IP CL1 - CL3 - pass on forward path by core1 cause match VLAN 20 and CL1 as SRC IP drop on return path by core1 cause match VLAN 20 and not CL1 but CL3 as SRC IP
NEW QUESTION # 47
Examine the configuration of Core-1 and Core-2. AOS-CX switches configured as a VSX stack:
Core1: Interlace lag 256
no shutdown
no routing
vlan trunk allowed all
lacp mode active Interface 1/1/46
no shutdown
lag 256 Interface 1/1/47
no shutdown
lag 256
VSX
Inter-switch-link lag 256
vsx-sync vsx-global
exit
Cofe2: interlace lag 250
no shutdown
no routing
vlan trunk allowed all
lacp mode active
Interlace 1/1/46
no shutdown
lag 256 Interface 1/1/47
no shutdown
lag 256 vsx
inter-switch-link lag 256
exit
When using the "show vsx status" command, the two switches fall to connect and successfully synchronize. What should the administrator do to fix this issue?
- A. Enable active-active forwarding on the two switches.
- B. Define the VSX roles on the two switches.
- C. Define a larger MTU on the ISL link of the two switches.
Answer: B
NEW QUESTION # 48
Examine the following AOS-CX configuration:
Based on this configuration, which statement is correct regarding IoT traffic?
- A. If 10.100.1.2 is not reachable, the IoT traffic will be automatically dropped by the switch
- B. All routes are ignored in the routing table for IoT traffic, which is routed to 10.100.1.2
- C. If a specific route is not available in the routing table, the traffic will be routed to 10.100.1.2
- D. The next hop of 10.100.1.2 can be one or more hops away from the AOS-CX switch
Answer: C
NEW QUESTION # 49
A network engineer is having a problem adding a custom-written script to an AOS-CX switch's NAE GUI.
The script was written in Python and was successfully added on other AOS-CX switches. The engineer examines the following items from the CLI of the switch:
What should the engineer perform to fix this issue?
- A. Ensure the engineer's desktop and the AOS-CX switch are synchronized to the same NTP server
- B. Install the script's signature before installing the new script
- C. Remove a script that is no longer used before installing the new script
- D. Enable trust settings for the AOS-CX switch's SSL certificate
Answer: C
NEW QUESTION # 50
Which protocols are used by NetEdit to interact with third-party devices? (Choose two.)
- A. telnet
- B. SSH
- C. Restful API
- D. CDP
- E. SNMP
Answer: B,E
NEW QUESTION # 51
......
HPE6-A73 certification exam is part of the Aruba Certified Switching Professional (ACSP) certification track. Aruba Certified Switching Professional Exam certification track is designed to validate the skills and knowledge of IT professionals who work with Aruba switching technologies. The ACSP certification track includes two exams: HPE6-A73 Aruba Certified Switching Professional and HPE6-A78 Aruba Certified Switching Expert.
HP HPE6-A73 Real 2024 Braindumps Mock Exam Dumps: https://www.troytecdumps.com/HPE6-A73-troytec-exam-dumps.html
HPE6-A73 Exam Questions | Real HPE6-A73 Practice Dumps: https://drive.google.com/open?id=1ESG7u-DSsYNkUcQup92C1M4zqQlqe-Mx