[Sep-2021] NACE NACE-CIP1-001 Dumps – Reduce Your Chance of Failure in NACE-CIP1-001 Exam
To help you achieve your ultimate goal, we suggest the actual NACE NACE-CIP1-001 dumps for your Coating Inspector Level 1 exam preparation to use as your guideline.
NEW QUESTION 38
The main responsibilities of the inspector are to
- A. observe and direct the work of the contractors.
- B. observe and report the quality of the work performed.
- C. direct and perform the work stated in the specification.
- D. demonstrate to the contractor how to apply the coating.
Answer: B
NEW QUESTION 39
Removal of surface contaminants is done by:
- A. Scarifying
- B. Waterjetting
- C. A combination of methods
- D. Abrasive blasting
Answer: C
NEW QUESTION 40
Osmotic blistering is most likely to occur as a result of
- A. overcoating a surface contaminated with chemical salts.
- B. airless spray application
- C. inadequate anchor pattern/surface profile.
- D. applying tine coating too thin.
Answer: B
NEW QUESTION 41
Which of these tests uses a syringe?
- A. Sleeve test
- B. Bresle patch
- C. Potassium ferricyanide
- D. Soluble salts meter
Answer: B
NEW QUESTION 42
You are asked to be the only coating inspector on a small bridge recoating job where existing coating contains lead. The owners' representative has supplied you with the local code governing the removal and disposal of lead based coatings, however upon reading the document you having great deal of difficulty understanding the technical language.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Carefully review the document and do the best you can
- B. Advise the owners' representative of your lack of knowledge in this area
- C. Hire a third patty to assist you in understanding the document
- D. Minimize your lack of understanding and go ahead with the inspection task to the best of your ability
Answer: A
NEW QUESTION 43
To achieve consistently accurate results with ALL alt test equipment
- A. wear gloves when sampling.
- B. calibrate the instrument in the field.
- C. wash your hands before sampling.
- D. avoid placing the sample discs on a surface.
Answer: C
NEW QUESTION 44
You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if the current trend continues, you expect to be outside specified conditions soon. The contractor advises you he is going to mix up the next full kit to complete his for the day.
Your FIRST preformed course of action is to:
- A. Advise the Contractor of your readings
- B. Call your supervisor
- C. Advise the Contractor he can proceed
- D. Advise the Contractor he cannot proceed
Answer: A
NEW QUESTION 45
Due to a previous premature coating failure the owner has required the original coating applicator to return to remove and replace 10,000 square feet of a failed three coat system at the applicator's cost. Due to the financial implications of another failure, the owner has offered you the job as the NACE CIP Level 1 Coating Inspector and explained that he expects you to be his "insurance policy" for this job. You have never been involved in a warranty job before and are unfamiliar with the coating system.
Your preferred FIRST course of action is to:
- A. Review the Product Data Sheets, and conduct a walk thru of the job site prior to the pre-job Conference
- B. Review the Product Data Sheets and meet with the Coating Applicator 'prior to the pre-job meeting
- C. Purchase Professional Liability Insurance prior to job commencement
- D. Meet with the owner and explain your limitations and concerns prior accepting the assignment
Answer: A
NEW QUESTION 46
The primary difference between Non-Convertible vs. Convertible coatings is:
- A. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
- B. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
- C. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not
- D. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do
Answer: D
NEW QUESTION 47
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?
- A. 80% of the specified minimum thickness
- B. 100% of the specified maximum thickness
- C. 90% of the specified maximum thickness
- D. 70% of the specified maximum thickness
Answer: A
NEW QUESTION 48
What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT) gauge?
- A. 6.35 cm (2.5 inch)
- B. 2.5 millimeters (.10 inch)
- C. 2.5 cm (1 inch)
- D. 1 cm (.39 inch)
Answer: C
NEW QUESTION 49
Removal of welds splatter is required:
- A. When NACE/SSPC abrasive blast standards are specified
- B. When ISO abrasive blast standards are specified
- C. When specifically identified in the owner's specification
- D. On every job
Answer: C
NEW QUESTION 50
The Inspector should record the serial numbers of inspection instruments:
- A. Only when verifying accuracy of the instrument
- B. Only if the instrument is suspected of not working properly
- C. Only if the specification requires it
- D. Each time the instrument is used
Answer: D
NEW QUESTION 51
Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:
- A. Rust Grades A-D
- B. Rust Grades 1-4
- C. Surface Condition H
- D. Surface Conditions E-G
Answer: A
NEW QUESTION 52
ISO SA 3 is directly equivalent to:
- A. NACE No. 2/SSPC SP 10
- B. NACE No. 1/SSPC SP 5
- C. None of the above
- D. NACE No. 3/SSPC SP 6
Answer: C
NEW QUESTION 53
Checking is
- A. surface breaks in the film that often result from grease or oil contamination and revel the substrate.
- B. a fine crack in the surface of a coating that rarely reaches the substrate
- C. an exposed area of the substrate or previous coat material, caused by poor application technique.
- D. a very small hole in a coating caused when air or solvent is trapped in porous film and then escapes.
Answer: B
NEW QUESTION 54
......
100% Free NACE-CIP1-001 Demo-Trial [Pdf], get it now: https://drive.google.com/open?id=1cQkNxwlBqhzZJHaasG_MWEJJYEDD1tqq
Accurate & Verified Answers As Seen in the Real Exam here: https://www.troytecdumps.com/NACE-CIP1-001-troytec-exam-dumps.html