TAKE CCNP Data Center 300-615 PRACTICE QUESTIONS FOR AMAZING RESULTS
Cisco 300-615 Exam Dumps Are Essential To Get Good Marks
How to book the Cisco 300-615: Troubleshooting Cisco Data Center Infrastructure Exam
These are the following steps for registering for the 300-615 exam.
- Step 1: Log into your account at Pearson VUE.
- Step 2: Select Proctored Exams and enter the exam number, 300-615.
- Step 3: Follow the prompts to register.
Who should take the Cisco 300-615: Troubleshooting Cisco Data Center Infrastructure Exam
The 300-615 exam test certification is an internationally-recognized validation that identifies persons who earn it as possessing skilled in Cisco 300-615: Troubleshooting Cisco Data Center Infrastructure i.e. Cisco routing and switching infrastructure devices like router, switches, etc. If a candidate/professional seeks a powerful improvement in career growth needs enhanced knowledge, skills, and talents. The Cisco 300-615: Troubleshooting Cisco Data Center Infrastructure Exam certification provides proof of this advanced knowledge and skill. If a candidate knows associated technologies and skills that are required to pass Cisco 300-615: Troubleshooting Cisco Data Center Infrastructure Exam then he should take this exam. These are candidates who should look for Cisco 300-615: Troubleshooting Cisco Data Center Infrastructure
- Cisco field support technicians
- Support engineers
NEW QUESTION # 64
Refer to the exhibit.
An engineer is troubleshooting why user1, user2, and user3 from group STORAGE- ADMINISTRATOR in Microsoft Active Directory cannot log in to the Cisco MDS SSH CLI. Which action resolves the issue?
- A. Configure SSH logins on Cisco MDS switch.
- B. Configure the role name to match the group name on Microsoft Active Directory.
- C. Integrate Cisco MDS with Microsoft Active Directory.
- D. Include specific users into MDS role configuration.
Answer: B
NEW QUESTION # 65
Refer to the exhibit.
The connection between a Cisco Nexus 5548UP switch and a Cisco MDS switch fails to initialize. What is the cause of the issue?
- A. The interface is in an incorrect mode.
- B. VSAN 1 is suspended.
- C. The SFP is unsupported.
- D. Trunk mode must be activated.
Answer: D
NEW QUESTION # 66
Refer to the exhibit.
A PC belongs to VLAN 68 The user experiences a large amount of packet loss when communicating with hosts that are outside of VLAN 68. Which action resolves the problem?
- A. Configure ip arp synchronization on both switches.
- B. Enable the peer-gateway feature
- C. Remove the HSRP configuration
- D. Replace HSRP with GLBP
Answer: B
Explanation:
Explanation
I assume that the PC is sending traffic with destination MAC of Nexus physical interfaces. If more snap shots about this question are available, please share.
NEW QUESTION # 67
Refer to the exhibit.
A network engineer has connected the Nexus switch management port to the Internet using DHCP to allow the Guest shell running on the switch to download Python packages. The engineer can ping google.com successfully from the Nexus switch, but the Guest shell failed to download any Python packages. Which action resolves the problem?
- A. Manually configure NTP in the Guest shell.
- B. Update the Python packages on the Cisco Nexus switch directly.
- C. Connect Guest shell to data plane interfaces to be able to connect to the networks outside the Cisco Nexus switch.
- D. Manually configure DNS in the Guest shell, even if it is claimed on the Cisco Nexus switch through DHCP.
Answer: D
NEW QUESTION # 68
Refer to the exhibit.
An OSPF adjacency between Router-A and Router-B cannot reach the FULL state. Which action resolves the issue?
- A. Set the OSPF media type to point-to-point.
- B. Disable the check of the MTU value.
- C. Adjust the MTU on Router-A to 1600.
- D. Adjust the MTU on Router-B to 1604.
Answer: B
NEW QUESTION # 69
Refer to the exhibit.
Refer to the exhibit. One of the vPC VTEPs fails to route VXLAN traffic to vPC connected hosts. When the issue was being diagnosed, it was discovered that the packets that were expected to be forwarded to the MAC address on the SWITCH-VTEP-1 are instead forwarded to the MAC address on SWITCH-VTEP-2 and then dropped. Which action resolves the issue?
- A. Configure ip arp synchronize under the VPC domain on both peers
- B. Configure a distributed anycast gateway on both peers
- C. Configure a different secondary IP address for one of the vPC peers
- D. Configure peer-gateway under the VPC domain on both peers
Answer: D
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/command/reference/vpc/n5k-vpc-cr/n5k-vpc_cmds_i.html#:~:text=a%20port%20profile.-,ip%20arp%20synchronize,no%20form%20of%20this%20command.
NEW QUESTION # 70
An engineer is troubleshooting issues in Cisco UCS Director. Drag and drop the possible causes from the left onto the correct issues on the right.
Answer:
Explanation:
NEW QUESTION # 71
Refer to the exhibit.
An engineer troubleshoots the HSRP configuration and notes that the remote end uses HSRP version 1. The engineer sets the local HSRP to version 1, but the problem continues. Which action resolves the issue?
- A. Set the local group number as 300 in the remote data center configuration
- B. Change the local group number to 255 or less and request that the remote data center matches the group member in its configuration.
- C. Reduce the priority of the local HSRP to below 100 to force the local HSRP to standby and then change the version to version 1.
- D. Run version 1 and version 2 HSRP on VLAN300 in the local data center.
Answer: B
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipapp_fhrp/configuration/xe-16/fhp-xe-16-book/fhp-hsrp-v2.p
NEW QUESTION # 72
An engineer is troubleshooting a custom AV pair that was created by a client on an external authentication server to map a read-only role for a specific security domain. Which AV pair solves the problem?
- A. shell=Security_Domain_1/Read_Role_1|Read_Role_2
- B. shell:domains=Security_Domain_1//Read_Role_1|Read_Role_2
- C. shell:domains=Security_Domain_1/Write_Role_1|Read_Role_2
- D. shell:domains=Security_Domain_1/Read_Role_1|Read_Role_2
Answer: B
NEW QUESTION # 73
Refer to the exhibit.
An engineer troubleshoots the HSRP configuration and notes that the remote end uses HSRP version 1. The engineer sets the local HSRP to version 1, but the problem continues. Which action resolves the issue?
- A. Set the local group number as 300 in the remote data center configuration
- B. Change the local group number to 255 or less and request that the remote data center matches the group member in its configuration.
- C. Reduce the priority of the local HSRP to below 100 to force the local HSRP to standby and then change the version to version 1.
- D. Run version 1 and version 2 HSRP on VLAN300 in the local data center.
Answer: B
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipapp_fhrp/configuration/xe-16/fhp-xe-16-book/fhp-hsrp-v2.p
NEW QUESTION # 74
Refer to an exhibit.
An engineer is troubleshooting an upgrade failure on a switch. Which action resolves the issue?
- A. Load a new system image.
- B. Save the system image in NVRAM.
- C. Use the same system image as the kickstart image.
- D. Reload the same system image.
Answer: A
NEW QUESTION # 75
After upgrading a client's fabric interconnect to the latest version, an engineer discovers that the appliance has lost its entire configuration. Which two locations should an engineer check to confirm that the appliance had backed up the configuration prior to the upgrade in order to retrieve the lost configuration? (Choose two.)
- A. Equipment FSM page, InternalBackup stage
- B. Equipment FSM page, PollInternalBackup stage
- C. Admin page, PollInternalBackup stage
- D. Service profiles page, InternalBackup stage
- E. Admin page, InternalBackup stage.
Answer: A,C
NEW QUESTION # 76
Refer to an exhibit.
An engineer is troubleshooting an upgrade failure on a switch. Which action resolves the issue?
- A. Load a new system image.
- B. Save the system image in NVRAM.
- C. Use the same system image as the kickstart image.
- D. Reload the same system image.
Answer: A
NEW QUESTION # 77
Refer to the exhibit.
An engineer is troubleshooting the connectivity between Server-1 and Server-2. Which action resolves the connectivity issue?
- A. Configure the same source IP address on NVE and virtual peer link on leaf switches
- B. Enable BGP advertise pip feature on both leaf switches
- C. Classify CFS messages for strict priority queue on spine switches
- D. Change all ports on spine switches as port-type fabric
Answer: C
NEW QUESTION # 78
An engineer is troubleshooting a fabric discovery failure. Which two requirements must an engineer verify about switch connectivity to solve the problem? (Choose two.)
- A. Leaf nodes must connect to spine nodes only.
- B. A Cisco APIC must be attached to a spine node only.
- C. A Cisco APIC must be attached to leaf nodes.
- D. Spine nodes must connect to other spine nodes.
- E. A Cisco APIC must be dual-attached to two separate spine nodes.
Answer: A,C
Explanation:
Section: Network
NEW QUESTION # 79
Refer to the exhibit.
An engineer is configuring boot from iSCSI on a Cisco UCS B-Series Blade Server, but the LUN fails to mount. Which action resolves the issue?
- A. Statically configure the target information in the Boot Policy.
- B. Configure a QoS policy on the vNIC.
- C. Set a connection timeout value of 250 in the iSCSI Adapter Policy.
- D. Configure an MTU size of 9000 on the appliance port.
Answer: A
NEW QUESTION # 80
......
Latest Cisco 300-615 Dumps with Test Engine and PDF (New Questions): https://www.troytecdumps.com/300-615-troytec-exam-dumps.html
Pass Your 300-615 Exam Easily - Real 300-615 Practice Dump Updated: https://drive.google.com/open?id=1JoJhOuffoOXbMxyq4kZuHi7fCHRlFmo7