[Jun-2024] 350-401 Exam Dumps - Free Demo & 365 Day Updates
Free Sales Ending Soon - Use Real 350-401 PDF Questions
Cisco 350-401 exam is intended for IT professionals who have experience in enterprise networking and want to validate their skills and knowledge. 350-401 exam is suitable for network administrators, network engineers, system engineers, and IT managers who want to advance their careers in the networking industry. Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) certification demonstrates the individual's expertise in implementing and managing enterprise-level network technologies, which is highly valued by employers.
To prepare for the Cisco 350-401 exam, candidates can use various study materials, including training courses, books, practice tests, and online resources. Cisco offers official training courses and study materials that cover all the exam topics and provide hands-on experience with Cisco equipment. Additionally, there are many online resources, such as forums and study groups, where candidates can connect with other IT professionals and share their knowledge and experience. With proper preparation, candidates can pass the Cisco 350-401 exam and obtain the Cisco Certified Specialist - Enterprise Core certification, which is a valuable credential in the IT industry.
NEW QUESTION # 41
Refer to the exhibit.
An engineer must configure HSRP for VLAN 1000 on SW2. The secondary switch must immediately take over the role of active router If the interlink with the primary switch fails. Which command set completes this task?
- A.
- B.
- C.
- D.
Answer: D
NEW QUESTION # 42
What is the result when an active route processor fails that combines NSF with SSO?
- A. The standby route processor immediately takes control and forwards packets along known routes.
- B. The standby route processor temporarily forwards packets until route convergence is complete.
- C. An NSF-aware device immediately updates the standby route processor RIB without churning the network.
- D. An NSF-capable device immediately updates the standby route processor RIB without churning the network.
Answer: A
Explanation:
Cisco Nonstop Forwarding does not maintain a continuously active control plane during switchover.
Instead, the forwarding plane uses known routes while the routing protocol information is being restored after switchover.
https://www.cisco.com/en/US/technologies/tk869/tk769/technologies_white_paper0900aecd801d c5e2.html
NEW QUESTION # 43
Which two characteristics apply to the endpoint security aspect of the Cisco Threat Defense architecture?
(Choose two.)
- A. cloud-based analysis of threats
- B. blocking of fileless malware in real time
- C. user context analysis
- D. outbound URL analysis and data transfer controls
- E. detect and black ransomware in email attachments
Answer: B,D
NEW QUESTION # 44
Which of the following are true statements regarding the Virtual Router Redundancy Protocol (VRRP) feature? (Choose two.)
- A. Pre-emption is enabled by default
- B. MD5 authentication is supported with VRRP
- C. Secondary IP addresses are supported with VRRP
- D. VRRP can only be used with Cisco devices
- E. The router priority is a configurable value from 0-4095
Answer: A,C
NEW QUESTION # 45
Drag and drop the virtual components from the left onto their deceptions on the right.
Answer:
Explanation:
NEW QUESTION # 46
Refer to the exhibit. What is output by this code?
- A. 0 1 2 3 4
- B. (0,5)
- C. 0 1 2 3 4 5
- D. 0 5
Answer: A
NEW QUESTION # 47
What is the benefit of using TCAM for IP forwarding decisions versus using the CAM table?
- A. TCAM processes lookups in a hardware CPU. and CAM relies on binary masks to find results.
- B. TCAM uses low cost hardware memory to store addresses, and CAM uses expensive hardware memory.
- C. TCAM finds results based on masks, and CAM finds results basing on exact match.
- D. TCAM finds results based on binary, and CAM uses the longest match to find results
Answer: A
Explanation:
The problem with CAM is that it can only do exact matches on ones and zeros (binary CAMs).
By implementing router prefix lookup in TCAM, we are moving process of Forwarding Information Base lookup from software to hardware.
NEW QUESTION # 48
Refer to the exhibit.
Based on the configuration in this WLAN security setting. Which method can a client use to authenticate to the network?
- A. certificate
- B. RADIUS token
- C. username and password
- D. text string
Answer: D
NEW QUESTION # 49
Drag and drop the characteristics from the left onto the switching architectures on the right.
Answer:
Explanation:
NEW QUESTION # 50
Drag and drop the characteristics from the left onto the orchestration tools they describe on the right.
Answer:
Explanation:
NEW QUESTION # 51
Refer to the exhibit.
The IP SLA is configured in a router. An engineer must configure an EEM applet to shut down the interface and bring it back up when there is a problem with the IP SLA. Which configuration should the engineer use?
- A. event manager applet EEM_IP_SLA
event sla 10 state unreachable - B. event manager applet EEM_IP_SLA
event sla 10 state down - C. event manager applet EEM_IP_SLA
event track 10 state down - D. event manager applet EEM_IP_SLA
event track 10 state unreachable
Answer: C
Explanation:
The ip sla 10 will ping the IP 192.168.10.20 every 3 seconds to make sure the connection is still up. We can configure an EEM applet if there is any problem with this IP SLA via the command event track 10 state down.
Reference: https://www.theroutingtable.com/ip-sla-and-cisco-eem/
NEW QUESTION # 52
Refer to the exhibit.
Refer to the exhibit. Which command set completes the ERSPAN session configuration?
- A. Option C
- B. Option B
- C. Option D
- D. Option A
Answer: D
NEW QUESTION # 53
Which device makes the decision for a wireless client to roam?
- A. access point
- B. WCS location server
- C. wireless client
- D. wireless LAN controller
Answer: C
NEW QUESTION # 54
Drag and drop the threat defense solutions from the left onto their descriptions on the right.
Answer:
Explanation:
NEW QUESTION # 55
Refer to the exhibit. Which type of antenna do the radiation patterns present?
- A. Dipole
- B. Patch
- C. Omnidirectional
- D. Yagi
Answer: B
Explanation:
A patch antenna, in its simplest form, is just a single rectangular (or circular) conductive plate that is spaced above a ground plane. Patch antennas are attractive due to their low profile and ease of fabrication.
The azimuth and elevation plane patterns are derived by simply slicing through the 3D radiation pattern. In this case, the azimuth plane pattern is obtained by slicing through the x-z plane, and the elevation plane pattern is formed by slicing through the y-z plane. Note that there is one main lobe that is radiated out from the front of the antenna. There are three back lobes in the elevation plane (in this case), the strongest of which happens to be 180 degrees behind the peak of the main lobe, establishing the front-to-back ratio at about 14 dB. That is, the gain of the antenna 180 degrees behind the peak is 14 dB lower than the peak gain.
Again, it doesn't matter if these patterns are shown pointing up, down, to the left or to the right.
That is usually an artifact of the measurement system. A patch antenna radiates its energy out from the front of the antenna. That will establish the true direction of the patterns.
Reference: https://www.cisco.com/c/en/us/products/collateral/wireless/aironet-antennas- accessories/prod_white_paper0900aecd806a1a3e.html
NEW QUESTION # 56
Which OSPF networks types are compatible and allow communication through the two peering devices?
- A. point-to-multipoint to nonbroadcast
- B. point-to-multipoint to broadcast
- C. broadcast to nonbroadcast
- D. broadcast to point-to-point
Answer: C
Explanation:
Reference:
The following different OSPF types are compatible with each other:
+ Broadcast and Non-Broadcast (adjust hello/dead timers)
+ Point-to-Point and Point-to-Multipoint (adjust hello/dead timers)
Broadcast and Non-Broadcast networks elect DR/BDR so they are compatible. Point-topoint/ multipoint do not elect DR/BDR so they are compatible.
NEW QUESTION # 57
Which IPv6 migration method relies on dynamic tunnels that use the 2002::/16 reserved address space?
- A. ISATAP
- B. GRE
- C. 6to4
- D. 6RD
Answer: C
Explanation:
6to4 tunnel is a technique which relies on reserved address space 2002::/16 (you must remember this range). These tunnels determine the appropriate destination address by combining the IPv6 prefix with the globally unique destination 6to4 border router's IPv4 address, beginning with the 2002::/16 prefix, in this format:
2002:border-router-IPv4-address::/48
For example, if the border-router-IPv4-address is 64.101.64.1, the tunnel interface will have an IPv6 prefix of 2002:4065:4001:1::/64, where 4065:4001 is the hexadecimal equivalent of
64.101.64.1. This technique allows IPv6 sites to communicate with each other over the IPv4 network without explicit tunnel setup but we have to implement it on all routers on the path.
NEW QUESTION # 58
Refer to the exhibit.
What is achieved by the XML code?
- A. It reads the output of the show ip access-list extended flp command into a dictionary list.
- B. It displays the output of the show ip access-list extended flp command on the terminal screen
- C. It displays the access list sequence numbers from the output of the show Ip access-list extended flp command on the terminal screen
- D. It reads the access list sequence numbers from the output of the show ip access-list extended flp command into a dictionary list.
Answer: D
NEW QUESTION # 59
Drag and drop the Qos mechanisms from the left to the correct descriptions on the right
Answer:
Explanation:
Explanation
A picture containing diagram Description automatically generated
NEW QUESTION # 60
Refer to the exhibit.
Refer to the exhibit Which two commands are required on route R1 to block FTP and allow all other traffic from the Branch 2 network' (Choose two)
- A. Option E
- B. Option B
- C. Option A
- D. Option D
- E. Option C
Answer: B,E
NEW QUESTION # 61
An engineer is concerned with the deployment of new application that is sensitive to inter-packet delay variance. Which command configures the router to be the destination of jitter measurements?
- A. Router(config)# ip sla responder udp-echo 172.29.139.134 5000
- B. Router(config)# ip sla responder tcp-echo 172.29.139.134 5000
- C. Router(config)# ip sla responder udp-connect 172.29.139.134 5000
- D. Router(config)# ip sla responder tcp-connect 172.29.139.134 5000
Answer: B
NEW QUESTION # 62
What is a characteristic of a next-generation firewall?
- A. filters traffic using Layer 3 and Layer 4 information only
- B. provides intrusion prevention
- C. required in each layer of the network
- D. only required at the network perimeter
Answer: B
Explanation:
A next generation firewall adds additional features such as application control, integrated intrusion prevention (IPS) and often more advanced threat prevention capabilities like sandboxing.
NEW QUESTION # 63
Refer to the exhibit.
A network engineer configures a GRE tunnel and enters the show Interface tunnel command. What does the output confirm about the configuration?
- A. Interface tracking is configured.
- B. The physical interface MTU is 1476 bytes.
- C. The tunnel mode is set to the default.
- D. The keepalive value is modified from the default value.
Answer: C
NEW QUESTION # 64 
Refer to the exhibit. What is the effect of introducing the sampler feature into the Flexible NetFlow configuration on the router?
- A. NetFlow updates to the collector are sent 50% less frequently.
- B. Every second IPv4 packet is forwarded to the collector for inspection.
- C. The resolution of sampling data increases, but it requires more performance from the router.
- D. CPU and memory utilization are reduced when compared with what is required for full NetFlow.
Answer: D
NEW QUESTION # 65
......
Automation (15%)
- Describing the high-level principles and benefits of the Yet Another Next Generation (YANG) language;
- Describing APIs for vManage and Cisco DNA Center;
- Constructing the EEM applet to automate data collection, troubleshooting, or configuration.
- Interpreting the basic Python components and scripts;
- Constructing the valid file utilizing the JSON code;
350-401 Dumps - Pass Your Certification Exam: https://www.troytecdumps.com/350-401-troytec-exam-dumps.html
Latest Real Cisco 350-401 Exam Dumps Questions: https://drive.google.com/open?id=1OEPlWugRa5S-RYFvCkmIDI3J5TbHcW6J